插头相机插头数码相机插头数码插头数码相机配件插头
fpc连接器fpc插座fpc连接座fpc插座连接器
ffc连接器ffc插座ffc插座连接器ffc插头座
产 品 规 格 书
product specification
【1】适用范围scope
本规格书适用于:0.5间距柔性扁平电缆连接器(有锁式)
this specification covers the 0.5mm pitch fpc/ffc connectors(series locking)
【2】产品名称及型号product name and part number
产品名称product name 产品型号part number
ffc/fpc扁平电缆连接器
【3】定格ratings
项目 item 规 格 requirement
大容许电压
rated voltage(max) 50v [ac/dc(有效值virtual value)50hz]
大容许电流
rated current(max) 0.4a
使用温度范围
ambient temperature range -25℃~+85℃
【4】性能performance
4.1电气性能electrical performance
项目item 条 件 test condition 规格requirement
4.1.1 接触电阻
contact resistance 适合fpc/ffc嵌合;开放电压20mv以下;短路电流10ma的状态下测定。
mate applicable fpc/ffc and measure by dry circuit,20mv max,10ma. ≤20 mωmax
4.1.2
绝缘电阻
insulation resistance 适合fpc/ffc嵌合;相邻端子间或端子与地面间加dc 500v下测定。
mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground. 500mωmin
4.1.3
耐电压
dielectric 适合fpc/ffc嵌合;相邻端子间或端子与地面间加ac 200v(有效值)历时1分钟下测定。
mate applicable fpc/ffc and apply 200v ac(virtual value)for 1minute between adjacent terminal or ground. 无击穿现象
no breakdown
4.2机械性能mechanical performance
项目item 条 件 test condition 规格requirement
4.2.1 锁紧力及拔出力
locking and withdrawal force适合0.3mm厚的ffc;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。
insert and extract applicable ffc at the speed rate of 25±3mm/minute. 锁紧力locking
1.96*n (n) max
拔出力withdrawal
0.49*n (n) min
4.2.2 端子保持力
terminal /housing retention force 以用每分钟25±3mm的速度平行向外拉
pull the terminal at the speed rate of 25±3mm per minute 3.92n min
4.3环境和其他性能environmental performance and others
项目item 条 件 test condition 规格requirement
4.3.1 重复插拔
repeated insertion and withdrawal 无通电状态;以10次/分钟的速度插拔20次
insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute 接触抵抗
contact resistance 60 mωmax
4.3.2 温度上升
temperature rise 适合fpc/ffc嵌合;大容许电流通电,温度测定。(ul 498)
carrying rated current load.(ul 498) 温度上升
temperature rise 30℃max
项目item 条 件 test condition 规格requirement
4.3.3
耐振动性
vibration dc 1ma通电状态下;嵌合轴沿xyz三个方向振动;振幅1.5mm;频率10-55-10hz/分;历时2小时
amplitude:1.5mmp-p
sweep time:10-55-10hz in 1 minute
duration:2 hours in each x.y.z. axes 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax瞬断
discontinuity 1 ms max.
4.3.4
耐冲击性
shock dc 1ma通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50g}冲击;各3次
490m/s2{50g},3 strokes in each x.y.z. axes. 外观
appearance 无损坏
no damage瞬断
discontinuity 1 ms max.
4.3.5
耐热性
heat
resistance 适合fpc/ffc嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时
85±2℃,96 hour外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
4.3.6
耐寒性
cold
resistance 适合fpc/ffc嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时
-40±2℃,96 hour 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
4.3.7
耐湿性
humidity
适合fpc/ffc嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
temperature:40±2℃
relative humidity:90-95%
duration:96 hours 外观
appearance 无损坏
no damage
接触抵抗
contact resistance 60 mωmax
耐电压
dielectric
strength 必须满足4.1.3
must meet 4.1.3绝缘抵抗
insulation resistance 20 mω min
4.3.8
温度循环
temperature
cycling 适合fpc/ffc嵌合;-55±3℃30分钟;常温常湿10-15分钟;85±2℃30分钟;常温常湿10-15分钟,循环5次。
5 cycles of:
a) -55±3℃ 30 minutes
b) 85±2℃ 30 minutes 外观
appearance 无损坏
no damage接触抵抗
contact resistance 60 mωmax
项目item 条 件 test condition 规格requirement
4.3.9
耐盐雾性
salt spray 适合fpc/ffc嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。
48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃. 外观
appearance 无损坏、腐蚀
no damage接触抵抗
contact resistance 60 mωmax
4.3.10
耐亚酸
so2 gas 适合fpc/ffc嵌合;40±2℃、50±5ppm的亚酸中放置24小时
24 hours exposure to 50±5ppm. so2 gas at 40±2℃. 接触抵抗
contact resistance 60 mωmax
4.3.11
耐性
nh3 gas 适合fpc/ffc嵌合;浓度为28%的水容器中;放置40分钟。
40 minutes exposure to nh3 gas evaporating from 28% ammonia solution 外观
appearance 无损坏
no damage 接触抵抗
contact resistance 60 mωmax
4.3.12
可焊性
solder ability 端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。
soldering time:2±0.5 sec.
soldering temperature:235±5℃
0.2 mmfrom terminal tip 沾敷性
solder wetting 沾敷面积95%以上
4.3.13
耐焊接热
resistance to
soldering heat 端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。
soldering time:5±0.5 sec.
soldering temperature:260±5℃
0.2 mmfrom terminal tip 外观
appearance 无损坏、变形
no damage
reference standard
:参考单位reference unit
【5】外观形状、寸法及材质product shape,dimensions and materials
图面参照refer to the drawing.
名称 name 材质 materials
主体main body lcp(本色) ul 94v-0
锁扣housing lock lcp(黑色) ul 94v-0
端子sit uip磷青铜 phosphor bronze
焊片contact 磷青铜 phosphor bronze
备注remark 金属表面镀锡
线长 : 40-400(mm) ;
形状 : 条形 ;
读卡类型 : micro ;
支持卡数 : 单卡 ;
接口类型 : zif ;
应用范围 : 显示屏 ;
种类 : ffc/fpc ;
型号 : fpc连接器.fpc0.5mm/1.0mm/1.25mm.全国专业连接器制造商.产品全.质量保证 ;
品牌 : 国产 ;
详细介绍
深圳市钜硕电子有限公司其他商品
手机连接器相关分类
- 插头、插座
- AC-DC连接器
- 端子(terminal)
- 电脑连接器
- 电缆连接器
- USB连接器
- PCB连接器
- 电源连接器
- 线束、连接线、端子线
- 汽车连接器
- 通讯连接器
- 手机连接器
- 端子排、接线排(条)
- 闭端子(压线帽)
- 端子盘
- 屏线、斑马纸
- 传感器连接器
- 鳄鱼夹、弹簧夹、电瓶夹
- 端子台、接线柱(头)
- 光纤端子
- 接线座、接线板
- 扬声器(喇叭)连接器
- 排针、排母、排线
- 转接头
- 电池连接器
- HDMI连接器
- 水晶头
- AV连接器
- IC连接器
- 汇流排(总线)
- 针座、插针
- 简牛、牛角
- S-video端子
- DispalyPort
- 板对线连接器
- WAFER连接器
- 显示屏连接器
- 1394连接器
- BNC连接器
- DVI连接器
- SCSI连接器
- 卡座(读卡器连接器)
- 护套
- 射频同轴(RF)连接器
- LED连接器
- 线对线连接器
- DC-DC连接器
- RJ45连接器
- D-SUB(VGA)端子
- IDC连接器
- 板对板连接器
- SATA、ATA连接器
- 光纤连接器
- 胶壳(housing)
- ZIF连接器
- PCI连接器
- DIN(大、中、小)
- FFC、FPC连接器
- IPOD连接器
- HDR连接器
- 背板连接器
- PLCC连接器
- 端子接插件
- 航空连接器