产 品 规 格 书
product specification
【1】适用范围 scope
本规格书适用于:0.5间距柔性扁平电缆连接器(有锁式)
this specification covers the 0.5mm pitch fpc/ffc connectors(series locking)
【2】产品名称及型号 product name and part number
产品名称product name
产品型号part number
ffc/fpc扁平电缆连接器
【3】定格 ratings
项目 item
规 格 requirement
大容许电压
rated voltage(max)
50v[ac/dc(有效值 virtual value)50hz]
大容许电流
rated current(max)
0.4a
使用温度范围
ambienttemperature range-25℃~ +85℃
【4】性能 performance
4.1电气性能 electrical performance
项目item
条 件 test condition
规格requirement
4.1.1
接触电阻
contact resistance
适合fpc/ffc嵌合;开放电压20mv以下;短路电流10ma的状态下测定。
mate applicable fpc/ffc and measure by dry circuit,20mv max,10ma.
≤20 mωmax
4.1.2
绝缘电阻
insulation resistance
适合fpc/ffc嵌合;相邻端子间或端子与地面间加dc 500v下测定。
mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground.
500mωmin
4.1.3
耐电压
dielectric
适合fpc/ffc嵌合;相邻端子间或端子与地面间加ac 200v(有效值)历时1分钟下测定。
mate applicable fpc/ffc and apply 200v ac(virtual value)for 1minute between adjacent terminal or ground.
无击穿现象
no breakdown
4.2机械性能 mechanical performance
项目item
条 件 test condition
规格requirement
4.2.1
锁紧力及拔出力
locking and withdrawal force
适合0.3mm厚的ffc;用每分钟25±3mm的速度;平行地插入、锁紧、拔出。
insert and extract applicable ffc at the speed rate of 25±3mm/minute.
锁紧力locking
1.96*n (n) max
拔出力withdrawal
0.49*n (n) min
4.2.2
端子保持力
terminal /housing retention force
以用每分钟25±3mm的速度平行向外拉
pull the terminal at the speed rate of 25±3mm per minute
3.92n min
4.3环境和其他性能 environmental performance and others
项目item
条 件 test condition
规格requirement
4.3.1
重复插拔
repeated insertion and withdrawal
无通电状态;以10次/分钟的速度插拔20次
insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute
接触抵抗
contact resistance
60 mωmax
4.3.2
温度上升
temperature rise
适合fpc/ffc嵌合;大容许电流通电,温度测定。(ul 498)
carrying rated current load.(ul 498)
温度上升
temperature rise
30℃max
项目item
条 件 test condition
规格requirement
4.3.3
耐振动性
vibration
dc 1ma通电状态下;嵌合轴沿xyz三个方向振动;振幅1.5mm;频率10-55-10hz/分;历时2小时
amplitude:1.5mm p-p
sweep time:10-55-10hz in 1 minute
duration:2 hours in each x.y.z. axes
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
瞬断
discontinuity
1 ms max.
4.3.4
耐冲击性
shock
dc 1ma通电状态下;嵌合轴沿相互垂直的6个方向;以490m/s2{50g}冲击;各3次
490m/s2{50g},3 strokes in each x.y.z. axes.
外观
appearance
无损坏
no damage
瞬断
discontinuity
1 ms max.
4.3.5
耐热性
heat
resistance
适合fpc/ffc嵌合;85±2℃的空气中;放置96小时;再回到室温中放置1-2小时
85±2℃,96 hour
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
4.3.6
耐寒性
cold
resistance
适合fpc/ffc嵌合;-40±2℃的空气中;放置96小时;再回到室温中放置1-2小时
-40±2℃,96 hour
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
4.3.7
耐湿性
humidity
适合fpc/ffc嵌合;40±2℃、相对湿度90-95%的空气中;放置96小时;再回到室温中0.5小时内测定
temperature:40±2℃
relative humidity:90-95%
duration:96 hours
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
耐电压
dielectric
strength
必须满足4.1.3
must meet 4.1.3
绝缘抵抗
insulation resistance
20 mωmin
4.3.8
温度循环
temperature
cycling
适合fpc/ffc嵌合;-55±3℃ 30分钟;常温常湿 10-15分钟;85±2℃ 30分钟;常温常湿 10-15分钟,循环5次。
5 cycles of:
a) -55±3℃ 30 minutes
b) 85±2℃ 30 minutes
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
项目item
条 件 test condition
规格requirement
4.3.9
耐盐雾性
salt spray
适合fpc/ffc嵌合;35±2℃、5±1%的盐水喷雾48小时;试验后常温水洗;再室温干燥。
48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃.
外观
appearance
无损坏、腐蚀
no damage
接触抵抗
contact resistance
60 mωmax
4.3.10
耐亚酸
so2 gas
适合fpc/ffc嵌合;40±2℃、50±5ppm的亚酸中放置24小时
24 hours exposure to 50±5ppm. so2 gas at 40±2℃.
接触抵抗
contact resistance
60 mωmax
4.3.11
耐性
nh3 gas
适合fpc/ffc嵌合;浓度为28%的水容器中;放置40分钟。
40 minutes exposure to nh3 gas evaporating from 28% ammonia solution
外观
appearance
无损坏
no damage
接触抵抗
contact resistance
60 mωmax
4.3.12
可焊性
solder ability
端子前端基准面0.2mm处浸入235±5℃的锡槽中;历时2±0.5 sec。
soldering time:2±0.5 sec.
soldering temperature:235±5℃
0.2 mm from terminal tip
沾敷性
solder wetting
沾敷面积95%以上
4.3.13
耐焊接热
resistance to
soldering heat
端子前端基准面0.2mm处浸入260±5℃的锡槽中;历时5±0.5 sec。
soldering time:5±0.5 sec.
soldering temperature:260±5℃
0.2 mm from terminal tip
外观
appearance
无损坏、变形
no damage
( ):参考规格reference standard
{ }:参考单位reference unit
【5】外观形状、寸法及材质product shape,dimensions and materials
图面参照 refer to the drawing.
名称 name
材质 materials
主体main body
lcp(本色) ul 94v-0
锁扣housing lock
lcp(黑色) ul 94v-0
端子sit uip
磷青铜 phosphor bronze
焊片contact
磷青铜 phosphor bronze
备注remark
金属表面镀锡
针数 : 4-60 ;
芯数 : 4-60pin ;
绝缘体材质 : lcp ;
接触件材质 : 磷铜 ;
特性 : 防潮 ;
制作工艺 : 熔接 ;
线长 : 40-400(mm) ;
形状 : 条形 ;
读卡类型 : mini sd ;
支持卡数 : 多合一 ;
接口类型 : zif ;
应用范围 : 汽车 ;
工作频率 : 低频 ;
种类 : ffc/fpc ;
型号 : js-a46561112 ;
品牌 : 钜硕 ;
行车记录仪连接器
- 供应商:
- 深圳市钜硕电子有限公司 进入商铺
- 所在分类:
- 电子元件
- 报价:
- 电讯
- 型号
- 不限
- 所在地:
- 观兰街道办环观中路37栋标准厂房.
- 联系电话:
- 86*************3578
- 手机:
- 137****9518
- 在线咨询:
- 留言/咨询
- 联系人:
- 幸*新
- 在线下单:
- 我要下单
详细介绍
深圳市钜硕电子有限公司其他商品