产 品 规 格 书product specification【1】适用范围 scope本规格书适用于：0.5间距柔性扁平电缆连接器（有锁式）this specification covers the 0.5mm pitch fpc/ffc connectors（series locking）【2】产品名称及型号 product name and part number 产品名称product name产品型号part numberffc/fpc扁平电缆连接器 【3】定格 ratings 项目 item规 格 requirement大容许电压rated voltage(max)50v[ac/dc(有效值 virtual value)50hz]大容许电流rated current(max)0.4a使用温度范围ambienttemperature range-25℃～ +85℃ 【4】性能 performance4.1电气性能 electrical performance 项目item条 件 test condition规格requirement 4.1.1接触电阻contact resistance适合fpc/ffc嵌合；开放电压20mv以下；短路电流10ma的状态下测定。mate applicable fpc/ffc and measure by dry circuit，20mv max，10ma.≤20 mωmax 4.1.2 绝缘电阻insulation resistance适合fpc/ffc嵌合；相邻端子间或端子与地面间加dc 500v下测定。mate applicable fpc/ffc and apply 500v dc between adjacent terminal or ground.500mωmin 4.1.3 耐电压dielectric适合fpc/ffc嵌合；相邻端子间或端子与地面间加ac 200v（有效值）历时1分钟下测定。mate applicable fpc/ffc and apply 200v ac（virtual value）for 1minute between adjacent terminal or ground.无击穿现象no breakdown 4.2机械性能 mechanical performance项目item条 件 test condition规格requirement4.2.1锁紧力及拔出力locking and withdrawal force适合0.3mm厚的ffc；用每分钟25±3mm的速度；平行地插入、锁紧、拔出。insert and extract applicable ffc at the speed rate of 25±3mm/minute.锁紧力locking1.96*n (n) max拔出力withdrawal0.49*n (n) min4.2.2端子保持力terminal /housing retention force以用每分钟25±3mm的速度平行向外拉pull the terminal at the speed rate of 25±3mm per minute3.92n min 4.3环境和其他性能 environmental performance and others项目item条 件 test condition规格requirement 4.3.1重复插拔repeated insertion and withdrawal无通电状态；以10次/分钟的速度插拔20次insertion and withdrawal actuator up to 20 cycles at the speed rate of less than 10 cycles/minute接触抵抗contact resistance60 mωmax4.3.2温度上升temperature rise适合fpc/ffc嵌合；大容许电流通电，温度测定。（ul 498）carrying rated current load.（ul 498）温度上升temperature rise30℃max 项目item条 件 test condition规格requirement 4.3.3 耐振动性vibrationdc 1ma通电状态下；嵌合轴沿xyz三个方向振动；振幅1.5mm；频率10-55-10hz/分；历时2小时amplitude：1.5mm p-psweep time：10-55-10hz in 1 minuteduration：2 hours in each x.y.z. axes外观appearance无损坏no damage接触抵抗contact resistance60 mωmax瞬断discontinuity1 ms max. 4.3.4 耐冲击性shockdc 1ma通电状态下；嵌合轴沿相互垂直的6个方向；以490m/s2{50g}冲击；各3次490m/s2{50g}，3 strokes in each x.y.z. axes.外观appearance无损坏no damage瞬断discontinuity1 ms max. 4.3.5 耐热性heatresistance适合fpc/ffc嵌合；85±2℃的空气中；放置96小时；再回到室温中放置1-2小时85±2℃，96 hour外观appearance无损坏no damage接触抵抗contact resistance60 mωmax 4.3.6 耐寒性coldresistance适合fpc/ffc嵌合；-40±2℃的空气中；放置96小时；再回到室温中放置1-2小时-40±2℃，96 hour外观appearance无损坏no damage接触抵抗contact resistance60 mωmax 4.3.7 耐湿性humidity 适合fpc/ffc嵌合；40±2℃、相对湿度90-95%的空气中；放置96小时；再回到室温中0.5小时内测定 temperature：40±2℃relative humidity：90-95%duration：96 hours外观appearance无损坏no damage接触抵抗contact resistance60 mωmax耐电压dielectricstrength必须满足4.1.3must meet 4.1.3绝缘抵抗insulation resistance20 mωmin 4.3.8 温度循环temperaturecycling适合fpc/ffc嵌合；-55±3℃ 30分钟；常温常湿 10-15分钟；85±2℃ 30分钟；常温常湿 10-15分钟，循环5次。5 cycles of： a) -55±3℃ 30 minutesb) 85±2℃ 30 minutes外观appearance无损坏no damage接触抵抗contact resistance60 mωmax 项目item条 件 test condition规格requirement 4.3.9 耐盐雾性salt spray适合fpc/ffc嵌合；35±2℃、5±1%的盐水喷雾48小时；试验后常温水洗；再室温干燥。48±4 hours exposure to a salt spray from the 5±1% solution at 35±2℃.外观appearance无损坏、腐蚀no damage接触抵抗contact resistance60 mωmax 4.3.10 耐亚酸so2 gas适合fpc/ffc嵌合；40±2℃、50±5ppm的亚酸中放置24小时24 hours exposure to 50±5ppm. so2 gas at 40±2℃.接触抵抗contact resistance60 mωmax 4.3.11 耐性nh3 gas适合fpc/ffc嵌合；浓度为28%的水容器中；放置40分钟。40 minutes exposure to nh3 gas evaporating from 28% ammonia solution外观appearance无损坏no damage接触抵抗contact resistance60 mωmax 4.3.12 可焊性solder ability端子前端基准面0.2mm处浸入235±5℃的锡槽中；历时2±0.5 sec。soldering time：2±0.5 sec.soldering temperature：235±5℃0.2 mm from terminal tip沾敷性solder wetting沾敷面积95%以上 4.3.13 耐焊接热resistance tosoldering heat端子前端基准面0.2mm处浸入260±5℃的锡槽中；历时5±0.5 sec。soldering time：5±0.5 sec.soldering temperature：260±5℃0.2 mm from terminal tip外观appearance无损坏、变形no damage ( )：参考规格reference standard{ }：参考单位reference unit【5】外观形状、寸法及材质product shape,dimensions and materials图面参照 refer to the drawing.名称 name材质 materials主体main bodylcp(本色) ul 94v-0锁扣housing locklcp(黑色) ul 94v-0端子sit uip磷青铜 phosphor bronze焊片contact磷青铜 phosphor bronze备注remark金属表面镀锡 导购推荐 品牌 钜硕 型号 js-a7078561234578912 种类 ffc/fpc 工作频率 低频 应用范围 电脑 接口类型 zif 支持卡数 多合一 读卡类型 mini sd 形状 条形 线长 40-400（mm） 制作工艺 熔接 特性 防潮 接触件材质 磷铜 绝缘体材质 lcp 芯数 4-60pin 针数 4-60